Javier Reto upgrading an FZ94

-


Last week I got an email from fellow roaster Javier Reto who purchased an early 2016 FZ-94 and is currently upgrading it to work fully with Artisan like my machine.

He has managed to speed up communications on the MODBUS following the procedure described by Marko Luther on his blog Bumping up MODBUS.

The new cable set to also add the frequency drives for air flow and drum speed have been ordered directly from CoffeeTech and these are in the mail on their way to Javier, so he will also be able to control these from within Artisan.

Currently (as of May 7 2017) the PID for ET is not yet willing to communicate. The correct SLAVE number setting has been set as can be seen here:



This is matching the configuration I also have in Artisan, with ID numbers ET=slave13, BT=slave11, DT=slave12:

I will add more info as we figure it out, which will be helpful to others upgrading their FZ94.

For those who need it, I placed some manuals for the Maxwell MTA-48k PID in a folder on my website.

Update late evening 7 May:
Javier found and solved the issue regarding communication of the ET PID: a wire was broken ;-)

So that was a simple one and studying the PID manuals was a useful exercise but not essential to solving this.

Javier closed up the front of the machine again and right away all three PIDs actively communicated:


So we may essentially do identical roasts now on locations extremely remote from one another, logging the roasts in the same way and when the new cables are there even adding the two frequency drives to the setup at Javier's end.

While I use the power sliders in Artisan and SSRs to regulate the energy in the elements, Javier can modulate this well like I did before, a combination of switching the elements on/off manually and regulating the airflow from within Artisan.

It would be nice to experiment with batches of beans from an identical harvest/shipment, do identical roasts and measure the roast color using the Tonino device (after calibrating our grind and tamp settings). We should be able to create the same roast results.

PS 12 May 2017:
Javier writes: "I spent $7 to get two cables and now I have it working!!  Fan and Drum are now capable of artisan control. "


Update 26 May 2017:
Tije built a Bean Trier Probe device for Javier:

27 May 2017:
Some more pictures of the preparations:













Update 14 June 2017: Dual probe arrived and partly installed




Update 17 June 2017 -- Tije's Trier Probe Device arrived and installed





Reacties

Een reactie posten

Populaire posts van deze blog

Tiny Cheap Fluid Bed Roaster by Tije and Jan

-
Afbeelding
(also see Daily Coffee News feature ) Tije designed and made the following structure for a tiny and cheap fluid bed roaster, to which Jan van der Weel added the Arduino parts, electronics and programming: Sketch by Tije de Jong Jan sourced a very cheap blower (€ 11) to start with, Tije developed and constructed the mechanics, Jan built together and programmed the TC4 / SSR electronics.  On his blog, Jan will specify exactly how the TC4 part is combined and programmed and I will copy these details into this blog entry, just as Jan will use this video in his blog. We did a few test roasts to make sure it works at all and it does. Towards the end, the first roast tended to get a flat BT line and airflow was slightly decreased. 200g seems max load of green beans. Second roast a little more power was given to the heater. Next we will try the Background Roast driven by the PID software of Artisan. A week later, with updated software that works better to change the fan
Meer lezen

Finished Pavoni & Fuji PXG4 pid: Probe Inside the Ring

-
Afbeelding
Delicious cup: all the work was well invested! At the end of the previous blog about the pressostat and PID working together , I mentioned that I would like to clean up the xmas tree of wires and have as few cables and probes as possible to visually disturb the classic design of the La Pavoni. Getting rid of the probe that was fastened with copper tape to the top of the brew group was a priority. I wanted to hide a new probe in the cooling fin as close as possible to the brew group. This morning I asked Tije if he could do that. He would need to drill a straight hole of 3mm diameter in the 4mm inner ring of the cooling fin that sits as a tight clamp around the brew group. Always the optimist, Tije set to work: First, Tije made a piece of aluminum to fit the inside of the ring. Drilling a thin hole straight through the curved aluminum, if possible tangentially going through the inside of the ring to touch the brew head directly, you need the support of the temporary insid
Meer lezen

TC4+ boards and Arduino controlled roaster by Matthias Gerstgrasser

-
Afbeelding
illustration by Matthias Gerstgrasser On the mailing list for Artisan users , Matthias Gerstgrasser posted a report about his coffee roaster project, with a link to a beautifully illustrated, complete step by step guide of his work on Instructables: A while ago I posted a few messages on here regarding automation for my hot-air popcorn roaster, and was asked if I could share a writeup of what I had been doing with my setup. I know it’s been a long time, but I haven’t forgotten, just got a little sidetracked (more on that below). I have finally found time to do this over the last few weeks though, and compiled a step-by-step guide of how I modified my popcorn machine. This is now available on Instructables: https://www.instructables.com/id/Arduino-controlled-DIY-Coffee-Roaster/   Do let me know if there’s anything missing or anything that could be improved. I intend to keep updating the guide as I find ways to improve it or as new developments occur. I am also discussing b
Meer lezen